Jump to content



Photo
- - - - -

Stubborn Tiptop On Loomis Imx 844c


  • Please log in to reply
6 replies to this topic

#1 Mickstix

Mickstix

    New Member

  • TU Member
  • Pip
  • 3 posts
  • Location:
    Debary, Florida

Posted 07 July 2012 - 10:35 PM

Hey all, I've got a Loomis IMX 844c (original, no repairs) and the tiptop won't stay put.. I used it forever throwing senkos and spinnerbaits, but recently started using it for flip/pitch 3/8-1/2oz t-rigs.. 30lb braid.. Anyway, aftere a couple trips the tip came loose (was cocked around backwards) so I removed it and put it back on with some "Laker Rod Cement" (guide glue) by following the directions on the label.. That lasted 1 trip.. Next I did it a little different. I heated the bare tip of the rod, removed excess glue, scuffed with a scotchbright, cleaned with acetone, shaved off small slices of the glue stick (Laker once again) and shoved them into the tiptop barrel, heated the barrel until glue went soft, reinstalled it and cleaned the access that came from both ends of the tiptop.. 1 more trip to the river and it's once again loose.. Does anyone have any ideas on solving this? Im thinkn' of using Devcon 2ton the next time, but wonder how that'll work out if I ever need to replace the tip again? Can you get a tip off, after it's been epoxied on? Or is there a better solution to my problem?? Thanks for any help! Mick

Edited by Mickstix, 07 July 2012 - 10:36 PM.


#2 RayburnGuy

RayburnGuy

    Advanced Member

  • TU Sponsor
  • PipPipPip
  • 3,647 posts
  • Location:
    Corrigan, Texas

Posted 07 July 2012 - 10:44 PM

I keep a bottle of super glue around just for that purpose. It's quick, can easily be stored in a tackle box for on the water repairs and holds up really well for me.

Ben

#3 Jig Man

Jig Man

    Advanced Member

  • TU Member
  • PipPipPip
  • 953 posts

Posted 08 July 2012 - 06:55 AM

I only use ferrule cement same as I do on my on my arrows. It holds and is easy to remove it you need to replace the rod tip at a later date.

#4 Mattman

Mattman

    Member

  • TU Member
  • PipPip
  • 281 posts
  • Location:
    Fergus Falls, MN

Posted 08 July 2012 - 07:35 AM

I use 5 minute epoxy on my tip tops. Once they're on, they're on. If you have to get them off for a repair or something, heat from an alcohol torch does the trick.

#5 Mickstix

Mickstix

    New Member

  • TU Member
  • Pip
  • 3 posts
  • Location:
    Debary, Florida

Posted 08 July 2012 - 10:58 PM

Thanks all!!

#6 Bob La Londe

Bob La Londe

    Advanced Member

  • TU Advertiser
  • PipPipPip
  • 1,454 posts
  • Location:
    Yuma, Az

Posted 19 July 2012 - 11:12 AM

I use 5 minmute epoxy all the time for tip tops. Works great and comes off easily with heat. I don't think I have ever had one come loose on its own if I took the time to remove all the plastic hot glue stick mess or glue from previous mounting and repairs.

After I have the old tip top off I gentley heat the tip of the rod to soften any old glue (DO NOT OVERHEAT AS YOU CAN DAMAGE THE ROD) and then I grab it hard with a rag and wipe all the old glue off.

#7 Braided Line

Braided Line

    Member

  • TU Member
  • PipPip
  • 210 posts
  • Location:
    Central Florida

Posted 25 July 2012 - 06:35 AM

No problem, I`ll fix it for you. I live just around the corner in Deltona. PM me.