All Activity

This stream auto-updates     

  1. Past hour
  2. Clear coat with Gorilla clear glue

    Wrong product. Gorilla glue makes a lot of different products now. You are referring to their initial water activated polyurethane formula. They have epoxies, silicone sealants, tape, and various other products now. The clear gorilla glue is a non foaming product (can even make it out on the poor picture above). I would not expect it to perform well as topcoat however based on it being "sandable". Not going to hurt to try it out on a scrap piece of wood and see how it performs. Now the white gorilla glue may be a good seal coat for balsa or other wood baits. Waterproof, sandable, paintable, etc... and white in color.
  3. 4 cavity creature/craw mold

    4.4 inch brand new craw mold shot it twice now buying a new punch bait mold I just seen posted $180 usd or $220 cdn
  4. Today
  5. 4.5" bull shad

    Here's a 4.5" bull shad in my bluegill pattern
  6. Using KBS clear coat

    So my order for some KBS clear coat came in today, I had to leave the 2 ton epoxy it was just too messy for me and time consuming (THATS JUST ME) but my question here is DO I SINGLE COAT MY LURES OR DOUBLE? and I will say i dunked about 25 crank baits I made and it took me only about 5 minutes total I LOVE HOW FAST I CAN COAT MY LURES NOW! also I barely used any clear coat so spending $50 on a quart of KBS will go a LOOOOONNNGGG WAAAAYYY! but I'm a newbie so will see. So yeah so far I've only dunked them once so should that be enough or should I do a second coat?? THANK YOU in advance!
  7. Ultra Molds Hand Injector?

    I'm on the other side of the fence. I really think I need or want a duel injector.
  8. Plumber's Lead

    Plumbers lead used in soil stacks and the like are general pretty pure .cant be beat
  9. How much powder paint per 100 spinnerbaits?

    Using TJ's spray gun, how much powder paint are you guys using to do , let's say 100 3/8 oz spinnerbaits? Sorry if it has been covered but couldn't find it
  10. Sealing a chugger

    I might have to go get some extra long cotton swabs from the drug store. I think thats what I'll have to try. I'l report back when I get them sealed one way or anther. Thanks Bob!
  11. Jiggy Bling

    I slotted an egg sinker to accept the hook then beat on it with a hammer to shape, not fancy but it worked. A little super glue, some abalone and three coats of epoxy, hand cut mylar strips.
  12. Muskie hook hanger size (greenhorn)

    we use wire0.62. .building cost effective in numbers of lures wire is less expensive then screw eyes...as for screws its an easier process. .both will hold up to musky,s..
  13. 20180217_185907.jpg

    Really like the "full" skirt. Gives that puppy some body. Another spinner bait for lilly pad fields on the St John`s. Very nice.
  14. Clear coat with Gorilla clear glue

    Gorilla glue needs moisture to cure and expands like foam. Wont flow out smooth and wont be very clear. Basically wont work
  15. Large 30 degree Swim Jig hook

    The Mustad 32850 is a heavy wire that comes in a 6/0. The only other one I know of that goes higher is the Mustad 91768 but I wouldn't call it a heavy wire but in an 8/0 or 9/0 I would think it would be heavy enough.
  16. Large 30 degree Swim Jig hook

    I don't know of any larger than 5/0. But, I would think that 5/0 would be plenty large enough for pike.
  17. Large 30 degree Swim Jig hook

    Does anyone know if there are 30 degree , preferably round bend heavy swim jig hooks in 6/0, 7/0, 8/0 sizes? I plan to try to use with the Do IT Bullet Bass Jig, larger size for Pike/Musky jigs? I see plenty of 60 degree and 90 degree hooks in these larger sizes, but I only see 28 and 30 degree hooks up to 5/0. Would prefer black nickel, but I am open to others. Any help is appreciated? Thanks in advance! Duckman
  18. Clear coat with Gorilla clear glue

    Had anyone used gorilla clear glue for clear coating baits. Got a bottle to do a couple of test on baits. Thanks for any advice or knowledge of clear coat.
  19. 20180217_185907.jpg

    100% handmade with living rubber.
  20. IMG_2077.jpg

  21. Chartreuse plastisol getting darker

    Frank has a YouTube video where he uses the griddle to keep the plastisol at a usable temp. You can also get a meat grinder from harbor freight and grind the sprue, it will heat with less time, and the heat stabilizer is a must.
  22. Plumber's Lead

    Some people ask their local mechanic to save them used tire weights.
  23. Yesterday
  24. Wanted to buy Molds or Existing Business

    Looking to purchase no longer used molds or an existing Business. Looking for frogs, mice, rats, trailer and swim bait molds. Please message me @ blackwidowtackleco@gmail.com
  25. Chartreuse plastisol getting darker

    look up frank an how he use his griddle.
  26. Sealing a chugger

    You can thin glue type epoxies like Devcon with a few drops of denatured alcohol. I don’t think thinner decoupage epoxies like Etex would need it. Just push a swab soaked in the epoxy through the hole from both ends several times and you should have good coverage.
  27. 1/2oz Classic Twin Spin

    Real nice work, smalljaw. Pretty fancy wire bending to attach the swivels, too!
  28. Chartreuse plastisol getting darker

    Short bursts of heat in the 20-30 second length along with smaller batches and heat stabilizer is all that even has a chance for me along with white.
  1. Load more activity