Jump to content
rapalaoutlet

Working On My First Swim Bait

Recommended Posts

So i am working on my first swim bait.. Already noticed some things i will be changing on the next 1.. I think defiantly the hinge will be changed and defiantly looking at using the aztek decking... here are some pics. this is made from a chunk of bass wood. still needs to be weighted and then sealed for the test run... the body itself is 4inches along with tail is a total of 5inches.. not sure how much i should weight it down but we shall see.. any ideas let me know.. for the tail i just used some plexiglass and notched out the tail section and inserted a pressure pin which allows the tail to swim freely..

IMG00422-20120320-1805.jpg

IMG00428-20120321-1518.jpg

IMG00422-20120320-1805.jpg

IMG00428-20120321-1518.jpg

IMG00422-20120320-1805.jpg

IMG00428-20120321-1518.jpg

IMG00422-20120320-1805.jpg

IMG00428-20120321-1518.jpg

IMG00422-20120320-1805.jpg

IMG00428-20120321-1518.jpg

IMG00422-20120320-1805.jpg

IMG00428-20120321-1518.jpg

IMG00422-20120320-1805.jpg

IMG00428-20120321-1518.jpg

IMG00422-20120320-1805.jpg

IMG00428-20120321-1518.jpg

post-26741-0-89175000-1332366939_thumb.jpg

post-26741-0-43911300-1332366962_thumb.jpg

Link to comment
Share on other sites

looks like a good start on swimbait making. you'll do more refining of your designs as you get more experience. do some searches on hinging to get more ideas. as far as ballast, i try to keep the ballast as low in the body of the bait as i can . if you want the bait to sink nose down put more ballast in the front segment. if you want it horizontal distribute the ballast in each segment. good luck and keep us posted on your progress.

jr

Link to comment
Share on other sites

here she is just needs a clear coat... it is currently 5 inches long and is 2.2 oz. i have done the clear coat it's just drying this pic was b4 the clear coat.. do not like how my paint came out at all should of planned it a bit better... however i can not complain about the rest.. def. a new hobby!

IMG00434-20120322-1200.jpg

IMG00434-20120322-1200.jpg

IMG00434-20120322-1200.jpg

IMG00434-20120322-1200.jpg

IMG00434-20120322-1200.jpg

IMG00434-20120322-1200.jpg

IMG00434-20120322-1200.jpg

IMG00434-20120322-1200.jpg

post-26741-0-88677500-1332452592_thumb.jpg

Link to comment
Share on other sites

Man, you're hooked now!

Nice job!

Here's a couple of key things I've found for getting good action from jointed swimbaits.

I've found that keeping the ballast out of the last section helps to insure maximum swimming action, and helps to keep the bait level on the retrieve.

Start at the head, and only add toward the rear if you run out of room in the first section.

Keeping the head section twice as long as the other sections helps to keep it more stable, and gives you more room for ballast.

Also, if you taper the bait from the top to the bottom, so it has a V profile, since there is less buoyant material on the belly, the bait won't roll on a fast retrieve. I usually start about 1/4 of the way down from the shoulder on a 7/8" thick bait, and taper to 5/8" at the belly. I don't have an exact formula, I just do it by eye.

You'll be happy if you give AZEK PVC a try. The decking, which is as buoyant as poplar, works really well for swimbaits. The trim board, which is more buoyant, is better for cranks.

You'll never have to worry about sealing your baits again, and water intrusion is never an issue.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...


×
×
  • Create New...
Top