gaspumper

TU Member
  • Content Count

    120
  • Joined

  • Last visited

  • Days Won

    1

Everything posted by gaspumper

  1. gaspumper

    Single row fluidbed

    cs coatings (component systems) has a fluid bed that will do up to 130 jigs (depending on size) at once.
  2. gaspumper

    Tackle shops near Detroit

    By the time you add the exchange rate its about the same price.
  3. gaspumper

    Tackle shops near Detroit

    Try Luremaking,com they are north west of Toronto.
  4. gaspumper

    Erie Rig Mold

    You did notice the original post is 10 yrs old.
  5. gaspumper

    Bulk powder paint

    There is a guy on site called "cadman" he has some colors in bulk
  6. gaspumper

    First Jigs Ever!

    Do-it has one like that called the weedless casting jig
  7. gaspumper

    Lee Precision Production Pot IV

    I took a drill bit the same size as the hole in the spout, and ran it through from the outside,you wouldn't believe the rust and crud that came out. I also took the plunger and cleaned the tip with emery cloth,I get very few drips now.
  8. gaspumper

    JIG DIPPING top coat

    Take a look at Pro Tec Glitter clear coat,goes on smooth and plenty of glitter.
  9. gaspumper

    SOFT CLEAN LEAD

    Says $1.50 per lb/ingots .No price for shipping,in the classified.
  10. gaspumper

    Painting dots

    There is 2 types of craft smart craft paint one say good to 350 degrees on the label,the other one doesn't have anything about heat on it.This is at Michaels.
  11. gaspumper

    Painting dots

    I use a craft paint called craftsmart,I powder paint my jigs then apply the eyes then put in the oven at 350 degrees for 20 min,the craft paint melts into the powder paint,as Eiron says .The craftpaint says its good at 350 degrees on the label.
  12. gaspumper

    Powder Paint Spray gun booth

    Thanks for the info,I guess it would serve it's purpose for certain applications.
  13. gaspumper

    Powder Paint Spray gun booth

    Smalljaw, approximately how much over spray would you reclaim on the 6 baits?
  14. gaspumper

    Prayer Jig Material

    Here is my version of a preacher jig ,I use a walleye head in 3/8-1/2- 3/4 oz. eagle claw 635B B/N Jig Hook, 5-6 inch bucktail and hackle 6-8".
  15. gaspumper

    Dyeing BUcktails

    sent you a pm
  16. gaspumper

    Looking for Shad Heads for In-Line Spinner

    No I do not pour these,but you can order the mold as suggested and pour your own ,just get a piece of stainless steel the diameter you need and lay across the mold close mold and tap lightly with a rubber mallet to make indent in mold.
  17. gaspumper

    Do-It Swimbait Head Jig Mold SBH-5-A Question

    The lead may be to hard ,try adding some soft lead to your mix.
  18. gaspumper

    Looking for Shad Heads for In-Line Spinner

    How about this head ,a little modification on the mold .Its called a diner shiner.
  19. gaspumper

    spinnerbait molds

    No you open the mold up ,you then drill a hole in the face of the mold where the wire rests on the mold as deep/thick as your magnet is making sure it is level with the face of the mold,then glue the magnet in .
  20. gaspumper

    Dyeing BUcktails

    I cleaned and cured 195 this yr. First I wash them in hot water and dawn dish soap,then after deboning I put them in a solution of water and alum for two weeks,then rinse and staple them on cardboard to dry,they come out like store bought.I use a dye called veniard dye its for feathers and hair. I only dye black, orange,yellow, red.
  21. gaspumper

    Porous fluid sheets

    I just use a brown sandwich bag for the filter material and strap a small 12 volt vibrator on the side of the cups along with the aquarium pump. All colors of paint fluidizes that way.
  22. gaspumper

    Ice jigs

    I use Craftsmart premium satan , it will take heat to 350 degrees.
  23. gaspumper

    Getting a small amount of paint

    And what has this to do with getting paint out of a can?????????
  24. gaspumper

    Fluid Bed??

    They are pretty easy to make but finding the proper filter material that works is the hard part.
  25. gaspumper

    airbrushing over powder paint?

    You know when all else fails read the directions,I looked on the tubes of acrylic paint I have here low and behold it says to cure 350 degrees for 30 min, I tried it on some jigheads I was working on,worked good and a lot cheaper then using the Testors model paint I was using.Thank you