Search the Community

Showing results for tags 'crank bait'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • TU Club Forums
  • General Discussions
    • TU Site Info & Updates
    • The Docks
  • Public Tackle Making Forums
    • Hard Baits
    • Soft Plastics
    • Wire Baits
    • Fly tying
    • Rod & Reel building & repair
    • Boatbuilding
    • Homebrew Tools
    • Hybrid Tackle
  • The Bait Shop
    • Classified Ads
    • TU Advertiser Forum
  • Knowledge Base
    • Member Submitted Tutorials
  • TU Events and Contests
    • TU Events
    • TU Lure Swap
  • Web Tools
  • News Archive
    • General News

Product Groups

  • TU Premium Membership
  • Advertisements
  • TU Swag

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests

Found 15 results

  1. Demon_dogg36

    Clear Jointed Swimbait blanks

    Any one here have info on unpainted swimbait blanks? 1 or 2 joints.
  2. ACarrell

    Juvenile Rainbow Trout

    This is my attempt at painting a juvenile rainbow trout, where they're going from the fingerling stage with the blotches into their adult coloration. If you have any suggestions, I will absolutely welcome them!

    © Andrew Carrell 2016

  3. barrybait

    20160625 203254[1]

    Another shad same as my previous post but with my now famous home made coffin bill. (thanks Mark Poulson) I enhanced my shad pattern and got the lower half shimmering with some Createx Wicked Aluminum, then to the bone colored belly. Also added pearl orange throat and tip of tail. Oh yeah, my dobbed eyes are getting better. I'm using the back end of a drill bit like before but now I am using the cheap acrylic paint, not air brush paint and I am able to get better painted eyes now.
  4. barrybait

    20160625 203740[1]

    Made this flatside balsa crankbait and used this pre made circuit board type lip from LPO. I have been making my own circuit board lips from the sheet purchased from LPO and they both work great. I used two 1/4" pieces of balsa to make the bait, epoxying them together after channeling them out for my weight and thru wire rig. For a weight I used a mojo weight which I cut in half length wise and had to drill out the center hole a little. Then I used the 19 gage ss wire, cut a long piece, put a twisted eye near the middle then ran both legs up thru my mojo weight, bending one forward tor another twisted line tie eye and the other aft to the rear hook hangar. Drilled 1/4" hole for the weight, seperated the halves and traced out the wires and hangars so I could channel out the balsa to accomodate the harness. Finished with Createx paints. I primer white then paint the bottom half gray and the upper half golden yellow. Scale mesh then paint bone on bottom, smoke the back with greatly reduced pearl black, then add some purple on the shoulder and remove the mesh. May have to enhance the golden yellow some after that but it is making a good shad pattern. Topped with D2T. Sized this similar to the coffin bill we used to get from Bustin Bass Baits or Evergreen on ebay but doesn't seem like we will be able to get them anymore. This works pretty well, even better than the coffin I think but it doesn't go quite as deep. About 5 feet.
  5. ELWE

    Walleye

    9", 6oz crank bait with belly bling and home brewed eyes. Foiled walleye pattern, made of pine.
  6. O'l Robzilla

    She said she wanted something red!

    No clear coat yet.

    © RLM

  7. O'l Robzilla

    Simple clean Bass.

    Just my take on a clean bass presentation.

    © RLM.

  8. O'l Robzilla

    The "Killer Gold Fish"!

    Just another out of the box design.

    © RLM.

  9. O'l Robzilla

    lure2

    Different colour variation, no clear coat yet.
  10. O'l Robzilla

    RLM 1857

  11. O'l Robzilla

    1655837 10154058351460440 477550435215056409 N

    Blue Gill type pattern.
  12. BigFisher

    Lime Lightning

    This is a 2.5 square bill crank bait with a one of a kind lighting pattern on the back that looks incredible I hope you like it.
  13. Cyberflexx

    Lures Painted on 9-10-2013

    I painted these last night and used a combination of createx and walmart acrylic paints, krylon crystal clear to help seal it, then used automotive clear coat sprayed from a air brush @ 35psi, 6 thin layers. Size 4 Laser Sharp hooks. What ya think?
  14. JoeyDaGreat

    Hard Bait Patterns

    Does anyone have a link to a good crank bait cookbook/patterns? I have seen the one pinned on top but I remember seeing one on this site or on another site that had a lot of patterns. Thanks for any info