Jump to content
fshng2

Poppers From Cork

Recommended Posts

Finally got around to using some old corks I found at a flea market last year.

Tools: Hacksaw, scapel (safety razor blades work too), sand paper 200 grit, latex gloves.

First I prime with 2 coats of exterior gloss white and let set for a day.

I used markers and then blended colors for the desired effect.

(Blending is achieved by quickly rubbing with a tissue that is slightly dampened with denatured alcohol.

If you are unhappy with the first results a clean alcohol dampened tissue can completely remove all marker.)

For the final top coat I used solarez, the thin version.

Lastly, hit with a UV light for a few minutes, then put in the sun to fully cure for a non tacky finish.

(A thin application of long curing epoxies also work well for top coat.)

2016-08-11 20.10.30.jpg

The first one floats half submerged, and the second one is 2/3 submerged.

I'll let the fish decide which is better

2016-08-11 20.31.14.jpg2016-08-11 20.23.46.jpg

2016-08-11 20.23.19.jpg2016-08-11 20.24.05.jpg

2016-08-11 20.10.30.jpg

2016-08-11 20.24.05.jpg

2016-08-11 20.23.46.jpg

2016-08-11 20.23.19.jpg

2016-08-11 20.31.14.jpg

2016-08-11 20.10.30.jpg

2016-08-11 20.24.05.jpg

2016-08-11 20.23.46.jpg

2016-08-11 20.23.19.jpg

2016-08-11 20.31.14.jpg

2016-08-11 20.10.30.jpg

2016-08-11 20.24.05.jpg

2016-08-11 20.23.46.jpg

2016-08-11 20.23.19.jpg

2016-08-11 20.31.14.jpg

2016-08-11 20.10.30.jpg

2016-08-11 20.24.05.jpg

2016-08-11 20.23.46.jpg

2016-08-11 20.23.19.jpg

2016-08-11 20.31.14.jpg

2016-08-11 20.10.30.jpg

2016-08-11 20.24.05.jpg

2016-08-11 20.23.46.jpg

2016-08-11 20.23.19.jpg

2016-08-11 20.31.14.jpg

2016-08-11 20.10.30.jpg

2016-08-11 20.24.05.jpg

2016-08-11 20.23.46.jpg

2016-08-11 20.23.19.jpg

2016-08-11 20.31.14.jpg

2016-08-11 20.10.30.jpg

2016-08-11 20.24.05.jpg

2016-08-11 20.23.46.jpg

2016-08-11 20.23.19.jpg

2016-08-11 20.31.14.jpg

post-47099-0-17257800-1470960844_thumb.jpg

post-47099-0-83940000-1470961592_thumb.jpg

post-47099-0-21871500-1470961610_thumb.jpg

post-47099-0-84989600-1470961623_thumb.jpg

post-47099-0-15076100-1470961949_thumb.jpg

Edited by fshng2
  • Like 1
Link to comment
Share on other sites

As  far as free corks goes.   Mondays is trash day in my neighborhood. Recycle  containers usually have plenty of wine bottles in them with corks.  Nice and clean. 

 

 As I`m walking my dog. I just grab the available corks and deposit them in a container in my work area.

     I`ve had to stop as my "supply" is more than enough.  

 

     With an excess of corks you can experiment in making things.  Some things work out while other "ideas"    just hit the floor.  

 

   Plus I`v crushed/powdered  some to fill in areas on some rod handles. Other stuff  included  in the mix as well.

Edited by Braided Line
Link to comment
Share on other sites

Would it be possible to have you demonstrate the basic assembly of this fine specimen for this noob?

It looks rather simple or basic but since I'm new to tying I'm asking noob questions.

I'm really liking the top one.

I've got a whole coffee can full of these wine corks ready. Just point the way! ;-)

Edited by Mr Ben
Link to comment
Share on other sites

Ahhh the cork oak from the Mediterranean area of Portugal and Southern France. For hundreds of years cork stoppers have been used to seal wine and other alcoholic drinks in bottles and barrels. Cork quality is visually determined. The outer observance of pits, infractions, non-circular shapes and the variety of visual imperfections, or not, determines cork grade. On 'select" grade cork, without any (or many) visual imperfections, the interior may be loaded with lentricels, similar to crevasses in glaciers, and what I call pointed burrs or hard enclosed knots. Since I drill three leg holes in all my top water popping bugs, I worry about hidden, internal gotchas. The pointed burrs or knots cause nearly all drill press drill bits to "walk" A leg hole through a bug eye is not appetizing. Pulling rubber legs through lentricels often causes a snag to compress then break off the rubber leg..

 

The world wide exploitation of cork has caused the quality to fall in the last few decades. No doubt what used to be a XX Laboratory grade cork is now a Select grade and previous discards have moved up to the ugly, broken XXXX so called Laboratory corks of today. Ground, glued, compressed cork, called agglomerated cork is used in wine bottles but makes a lousy popping bug bug because of all the extra weight. Other suppliers fill wine cork visual imperfections with adhesive and cork dust but this also increases weight but not as much as the agglomerated approach. I've found that either new, unused, high quality, "pricey" wine corks or discarded corks from wine in the $30-$40 range and up that were not opened with a cork screw are the best today.

 

I go into making popping bugs from wine corks in my book, "Big Bass Fly Fishing on Topwater A Field Guide" which you can find on my web site,

 

www.bigbassflyfishing.com/

 

Under BUGS, I have 22 patterns in three sizes I made from cork stoppers. I'm in the process of loading some of my unique fly tying tools and fly fishing accessories for Big Bass anglers.

 

Working cork is a challenge, I never know where the bit or saw or sander is going. It's much like landing a Big Bass LOL!

 

Good Luck.

John

  • Like 1
Link to comment
Share on other sites

John, I didn't realize this was you. I tried to call you to say thank you when the autographed copy arrived. I have your book in a place of honor right next to my autographed copy of Buckley's book on air gun building. Thank you. I rather enjoyed it. Well the first few chapters so far and of course flipping through to see all the pictures.

Link to comment
Share on other sites

Bob thank you for the kind words about my book. It's selling quite well, especially to Bass Fly Tournament guys who keep saying, "Don't sell it to my competitors!" LOL And with 149 Big Bass tips and 84 Big Bass family secrets, my son Lance said I omitted his two favorites - the ones that "always" work. He means my Lindsey Ozark Bumble Bee pattern number 19. There two ways to fish it - IGFA Compliant and NOT IGFA Compliant. Both ways start the same: Cast with the wind up next to flowering, floating material like water lilies. Keep tight line, leader and tippet. The IGFA Compliant method is to rap your knuckles on your fly rod just above your reel. This vibration often triggers a strike. The IGFA NON Compliant method is to turn on your cordless tooth brush and grasp it against your fly rod just above your reel. My up sized Ozark Bumble Bee with a tooth brush vibration works when nothing else does. I'm not a BASS tournament guy so I don't know if it's legal there but you would know.

 

Thanks again. I'll PM you.

John

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...


×
×
  • Create New...
Top