Jump to content
JR

Kwikpoly

Recommended Posts

Does anyone have any experience using a product called “Kwikpoly”? Please see www.kwikpolyllc.com . We use it as an electrical insulator where I work.

Is very thin and seems to soak deep into the balsa test strips I have used. Hasn't yellowed, as of yet ( 110 days ). It cures in about five minutes. Seems to be very tuff and flexible. I am going to try it as a top coat and a sealer to see how it works out. I normally stay away from the quick curing poly epoxies but this has caught my eye

Just wondering if anyone has tried it on a lure. Always looking for something new to play with.

Jack

Link to comment
Share on other sites

I will do it. I have had a test strip coated and laying in the window for some time. It hasn't yellowed yet but will be watching it over the next several weeks.

This stuff goes on like water but does set up fast. I chilled the mixture on ice and it lasted about 10 minutes, but really soaks in to the wood. I put two test coats on painted scrap balsa and it looks good. Has a deep gloss shine and seems to be tuff as anything I have used.

Jack

Link to comment
Share on other sites

It seems to level out well. I think the trick would be not to try to do too many t a time. The test strips I did looked fine just turning them by hand. You won't have to worry about the "in-between jell" you get with some epoxies. It either spreads or it is solid.

Jack

Link to comment
Share on other sites

Tally, I can not speak for everyone but in my opinion I like my initial seal coat to soak into the surface of the wood a bit. I find this especially beneficial on balsa and in some instances with jelutong (paya).

The epoxy penetrates the surface and forms a type of “ectoskeleton”, giving some strength and rigidity to the surface of the wood. It also provides a water-proofing that, I hope protects the wood in case of a leak in the final finish coat. One coat, perhaps two, does provide a very acceptable primer for following layers of finish. I have found you can cut the glaze of the two part sealer with fine sand paper, then coat with colored primer and get a good paint job.

I have found that a balsa lure sealed with conventional one-part sealers can be compressed with just finger pressure. If a two part epoxy type sealer is used and it has soaked into the surface of the material, it takes much more pressure to flex the surface of the lure. It is purely a strength thing with me.

I believe I first heard, ”custom bait makers tend to over build their baits“ here and I believe it may be true but it is just the way we are. I am always looking for a better product. I tend to come back to what I know, but I keep looking.

Jack

Link to comment
Share on other sites

Tally, you are more than welcome. I use Devcon also. It soaks in just past the surface layer. I am always looking for something that might soak in a bit further and still give me the same qualities as the Devcon.

Never not ask a question. If you don't ask is it still a question?

Jack

Link to comment
Share on other sites

Tally,

That was me that said that I didn't want anything to soak way down into the wood. I still want the bouyancy to be there. Balsa will take allot before it won't float. I still use the Devcon to coat my balsa lures before I paint them. Like JR said,,,, it doesn't soak way down into the wood.

But I am curious about the results of JRs experiment.

Skeeter

Link to comment
Share on other sites

I have gone ahead and cut out some body blanks from jelutong, balsa, and butternut. I have coated these with Kwikpoly and when they dried I cut one of each in half. I will look at these under magnification, at work, and hopefully know how far the coating really soaked in.

The more I play with this stuff the better I like it. I guess the real test will

be if it yellows or not and how well it holds up to some stress testing.

I will keep you posted.

Jack

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...


×
×
  • Create New...
Top